Safety Data Sheet

According to GHS (Global Harmonized System) - Hazcom 2012
Date Printed (YYYY-MM-DD): 2016-08-31 

Section 1 - Product and Company Information

Product Name: Putty Flex Bumper Glaze
Product Part Number(s): 1047
Recommended Use: Used for spot filling and skim coating over repair areas on flexible bumpers and plastic parts.
Revision Date (YYYY-MM-DD):

COMPANY IDENTIFICATION:EMERGENCY TELEPHONE NUMBER
Polyvance24 Hour Emergency ContactChemtrec - 1-800-424-9300 (Outside USA 703-527-3887)
1128 Kirk Rd.Customer Information Number256-638-4103 (7AM - 4PM (CST) M-F)
Rainsville, AL 35986
Information Email: info@polyvance.com

Section 2 - Hazards Identification

Appearance:Opaque, high viscosity, pourable liquid
Odor:Acrid
Hazard Statement:
 WARNING! Flammable liquid and vapor. Heating may cause an explosion. Causes mild skin irritation. Causes eye irritation.  

Signal Word:  

WARNING!
Signal Word Hazard:   Flammable Liquid
GHS Physical Hazard PictogramsGHS Health Hazard PictogramsGHS Environmental Hazard Pictograms

Flammable

Irritant

Health Hazard
Not Applicable

GHS Hazards Statement Codes for This Product

Statement
Type
Statement
Code
Statement Text
Physical H226 Flammable liquid and vapor
Physical H240 Heating may cause an explosion
Health H316 Causes mild skin irritation
Health H320 Causes eye irritation
Precautionary Statement:
 Keep out of reach of children. Read label before use. Keep away from heat/sparks/open flames/hot surfaces - No smoking. IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. IF ON SKIN: Wash with soap and water. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.  

GHS Precautionary Statement Codes for This Product

Statement
Type
Statement
Code
Statement Text
General P102 Keep out of reach of children
General P103 Read label before use
Prevention P210 Keep away from heat/sparks/open flames/hot surfaces - No smoking
Response P301+330+331 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting
Response P302+352 IF ON SKIN: Wash with soap and water
Response P304+340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing

Potential Health Effects

Eye Contact:May cause irritation. Liquid splashes may result in more serious injuries.
 
Skin Contact:Can dry and defat skin with resultant irritation and possible dermatitis.
 
Skin Absorption:Styrene may be absorbed through the skin in toxic amounts. May cause allergic reactions and systematic toxicity.
 
Inhalation:Dizziness, headaches, breathing difficulties, and possible narcosis. Prolonged exposure to high concentrations may be fatal.
 
Ingestion:May cause gastrointestinal disturbances, pain, and discomfort.
 

Section 3 - Composition/Information on Ingredients

Component CAS # ENIECS REACH Reg. No. Amount
 
Polyester Resin Proprietary 20-30%
Styrene 100-42-5 20-25%
Talc 14807-96-6 40-45%
Titanium Dioxide 13463-67-7 1-5%

Section 4 - First Aid Measures

Eye Contact: Flush with large amounts of water until all material is removed. If irritation persists, get medical attention immediately.
 
Skin Contact: Wash with soap and water. Remove contaminated clothing and was before re-use. Shower. If irritation persists, see physician.
 
Inhalation: Move to fresh air. Artificial respiration is necessary. Consult physician immediately.
 
Ingestion: Do not induce vomiting. Consult physician immediately.
 
Medical Conditions Aggravated by Exposure: Anesthesia, headache, respiratory irritation, dermatitis, allergic reactions, nausea, and vomiting.
 

Section 5 - Firefighting Measures

Extinguishing Media: Fight source of fire. Dry chemical, carbon dioxide, chemical foam.
 
Fire Fighting Procedures: Spray water to cool containers. If this material is involved in a fire, NIOSH approved, self-contained breathing apparatus should be worn.
 
Special Protective Equipment for Firefighters: NIOSH approved, self-contained breathing apparatus should be worn.
 
Unusual Fire and Explosion Hazards: Vapors are heavy and may concentrate at lower levels creating hazard. At high temperatures, containers may burst.
 
Hazardous Combustion Products: Chlorine, hydrogen chloride (hydrochloric acid), phosgene
 

Section 6 - Accidental Release Measures

Steps to be Taken if Material is Released or Spilled: Remove from ignition sources, ventilate area and vacate area. Allow solvents to evaporate.
 
Personal Precautions: Use personal protection recommended in Section 8.
 
Environmental Precautions:
 

Section 7 - Handling and Storage

General Handling: Wear gloves, goggles and protective clothing to prevent contact with product.
 
Other Precautions:
 
Storage: Store material in a cool dry place. Do not store containers in direct sunlight.
 

Section 8 - Precautions to Control Exposure / Personal Protection

ComponentSourceTypeValueRemarks
StyreneNIOSHIDLH700 ppm
StyreneACGIHTLV40 ppmSTEL
StyreneACGIHTLV20 ppmTWA
StyreneOSHAPEL100 ppmTWA
TalcACGIHTLV2 mg/m3TWA
TalcOSHAPEL20 mppcfTWA
Titanium DioxideACGIHTLV10 mg/m3TWA
Titanium DioxideOSHAPEL15 mg/m3TWA

Personal Protective Equipment (PPE):

Eye/Face Protection: Chemical splash goggles (ANSI Z 87.1 or approved equivalent)
 
Skin Protection: Polyvinyl gloves and apron. Wear protective clothing to prevent contact with product.
 
Respiratory Protection: None required if adequate ventilation is provided.
 
Hygenic Measures: Wash thoroughly after handling and before eating and drinking.
 
Engineering Controls: Use exhaust ventilation to keep airborne concentration below exposure limits.
 


Section 9 - Physical and Chemical Properties

Appearance: Liquid
 
Color: Beige
 
Odor: Acrid
 
ph: Not determined
 
Flash Point: 80°F (26° C)
 
Upper Flammable Limit: Not determined
 
Lower Flammable Limit: Not determined
 
Autoignition Temperature: Not determined
 
Vapor Pressure: Not determined
 
Boiling Point: >100°C
 
Vapor Density: Heavier than air.
 
Specific Gravity: 1.5
 
Freezing Point: Not available
 
Melting Point: Not available
 
Solubility in Water: Not determined
 
Evaporation Rate: Slower than n-Butyl Acetate
 
Partition Coefficient: Not available
 
Decomposition Temperature: Not determined
 
Percent Volitiles: 23%
 
Volitile Organic Compounds (VOC): 2.49 lbs/gal (279 grams/liter)
 
Visosity: Not available

Section 10 - Stability and Reactivity

Stability/Instability: Stable under normal conditions (70°F (21°C) and 14.7 psig (760 mm Hg))
 
Conditions To Avoid: Excessive heat and freezing temperatures
 
Incompatible Materials: Oxidizing agents, alkalies and high temperatures.
 
Hazardous Polymerization: Will not occur.
 
Hazardous Decomposition Products: Chlorine, hydrogen chloride (hydrochloric acid), phosgene.
 

Section 11 - Toxicological Information

Ingestion Toxicity: Not available
Skin Absorption:Not available
Inhalation
Not available
 
Sensitization
Not available
 
Acute Dose
Not available
 
Repeated Dose Toxicity
Not available
 
Chronic Toxicity and Carcinogenicity
Not available
 
Corrosivity
Not available
 
Neurological
Not available
 
Reproductive Toxicity
Not available
 
Genetic Toxicity
Not available
 
Eye Irritation
Not available
 
Skin Irritation
Not available
 
Target Organs
Not available
 

Section 12 - Ecological Information

Movement & Partitioning
Not available
 
Persistence and Degradability
Not available
 
ECOTOXICITY
Not available
 
Bioaccumulation:
Not available
 
Other Adverse EffectsNot available
 

Section 13 - Disposal Considerations

Disposal Method:
Disposal should be in accordance with applicable regional, national and local laws. Local regulations may be more stringent than regional or national requirements.
 
Container Disposal: Empty containers should be reconditioned by certified firms (drums, pails).
 

Section 14 - Transport Information

DOT

Proper Shipping Name: Polyester resin
 
ID Number: UN3269
 
Packing Group: III
 

Section 15 - Regulatory Information

Superfund Amendments and Reathorization Act of 1986 (Emergency Planning and Community Right-to-Know Act of 1986) Sections 311 and 312

The following table list hazardous components and the regulatory lists for which they are required to be reported.

Component: Styrene
CAS Number: 100-42-5
Amount: 20-25%
Styrene is listed in SARA 313
Styrene is listed with the Occupational Safety and Health Administration (OSHA) as a possible carcinogen.

Component: Talc
CAS Number: 14807-96-6
Amount: 40-45%
Talc is listed in SARA 313
Talc is listed with the Occupational Safety and Health Administration (OSHA) as a possible carcinogen.

Component: Polyester Resin
CAS Number: Proprietary
Amount: 20-30%

Component: Titanium Dioxide
CAS Number: 13463-67-7
Amount: 1-5%
Titanium Dioxide is listed in SARA 313
Titanium Dioxide is listed with the National Institute for Occupational Safety and Health (NIOSH) as a possible carcinogen.
Titanium Dioxide is listed with the Occupational Safety and Health Administration (OSHA) as a possible carcinogen.

HMIS Rating (Scale 0 - 4)

HEALTH  2  Health = 2
FIRE  3  Fire = 3
PHYSICAL  1  Physical = 1
PERSONAL PROTECTION G Personal Protection = G

NFPA Ratings

 3 
2 0
Health = 2
Fire = 3
Reactivity =0

Section 16 - Other Information

Legend
ACGIHAmerican Conference of Governmental Hygenists
ACGIHAmerican Conference of Governmental Hygenists
CASChemical Abstract Service
CFRCode of Federal Regulations
DFGDeutsche Forschungsgemeinschaft
EPAEnvironmental Protection Agency
HMISHazardous Materials Identification System
IARCInternational Agency for Research on Cancer
LTELLong Term Exposure Limit
MAKMaximum Allowable Concentration (German)
MSDSMaterial Safety Data Sheet
NFPANational Fire Protection Association
NIOSHNational Institute for Occupational Safety and Health
NTPNational Toxicology Program
NTPNational Toxicology Program
OELOccupational Exposure Limit
OSHAOccupational Safety and Health Administration
PELPermissible Exposure Limit
RCRAResource Conservation and Recovery Act
RELRecommended Exposure Level
STELShort Term Exposure Limit
TLVThreshold Limit Value
TSCAToxic Substances Control Act
TWATime Weighted Average
VOCVolitile Organic Compounds
WEELWorkplace Environmental Exposure Level

DISCLAIMER
This Safety Data Sheet (SDS) is prepared in compliance with GHS Hazcom 2012. The information may be based in part on information provided by component suppliers and is believed to be correct as of the date hereof. However, no warranty or merchantability, fitness for any use, or any other warranty is expressed or is to be implied regarding the accuracy of of this data, the results to be obtained from the use of the material, or the hazards connected with such use. Since the information contained herein my be applied under conditions beyond our control and with which we may be unfamiliar, and since data made available subsequent to the date hereof may suggest modification of the information, we assume no responsibility for the result of its use. This information and material is furnished on the condition that the person receiving it shall make his/her own determination as the the suitability of the material for his/her particular purpose and on the condition that he/she assume the risk of his/her use thereof.