Safety Data Sheet

According to GHS (Global Harmonized System) - Hazcom 2012
Date Printed (YYYY-MM-DD): 2018-01-31 

Section 1 - Product and Company Information

Product Name: Plastic Magic (aerosol)
Product Part Number(s):
Recommended Use: A surface modifier that eliminates the paint peeling problems on automotive plastics.
Revision Date (YYYY-MM-DD):

Polyvance24 Hour Emergency ContactChemtrec - 1-800-424-9300 (Outside USA 703-527-3887)
1128 Kirk Rd.Customer Information Number256-638-4103 (7AM - 4PM (CST) M-F)
Rainsville, AL 35986
Information Email:

Section 2 - Hazards Identification

Hazard Statement:
 DANGER! Flammable aerosol. Pressurized container: may burst if heated. Causes skin irritation. Causes eye irritation. Harmful if inhaled.  

Signal Word:  

Signal Word Hazard:   Extremely flammable liquid
GHS Physical Hazard PictogramsGHS Health Hazard PictogramsGHS Environmental Hazard Pictograms


Not Applicable

GHS Hazards Statement Codes for This Product

Statement Text
Physical H223 Flammable aerosol
Physical H229 Pressurized container: may burst if heated
Health H315 Causes skin irritation
Health H320 Causes eye irritation
Health H332 Harmful if inhaled
Precautionary Statement:
 Keep out of reach of children. Read label before use. Keep away from heat/sparks/open flames/hot surfaces - No smoking. Pressurized container - Do not pierce or burn, even after use. Do not get in eyes, on skin, or on clothing. Protect from sunlight. Store in a well ventilated place.  

GHS Precautionary Statement Codes for This Product

Statement Text
General P102 Keep out of reach of children
General P103 Read label before use
Prevention P210 Keep away from heat/sparks/open flames/hot surfaces - No smoking
Prevention P251 Pressurized container - Do not pierce or burn, even after use
Prevention P262 Do not get in eyes, on skin, or on clothing
Storage P410+403 Protect from sunlight. Store in a well ventilated place

Potential Health Effects

Eye Contact:Irritating to eyes
Skin Contact:Prolonged contact may cause slight irritation with local redness. May cause drying and flaking of the skin
Inhalation:Harmful by inhalation

Section 3 - Composition/Information on Ingredients

Component CAS # ENIECS REACH Reg. No. Amount
2-(propyloxy)ethanol 2807-30-9 <2.5%
2-Butanone 78-93-3 1-3%
2-methoxy-1-methylethyl acetate 108-65-6 <2.5%
Acetone 67-64-1 25-50%
Chlorinated Polyolefin N/A 0-1%
Heptane 142-82-5 45-50%
Isobutane/propane aerosol propellant 68476-86-8 3-5%
Petroleum gases, liquified, sweetened 68476-86-8 25-50%
Vinyl Acetate Copolymer 24937-78-8 0 1 %
Xylene 1330-20-7 10-25%

Section 4 - First Aid Measures

Eye Contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Skin Contact: Immediately was with water and soap and rinse thoroughly.
Inhalation: Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist.
Ingestion: After swallowing: if symptoms persist consult doctor.
Medical Conditions Aggravated by Exposure: Bronchitis, CNS disorders, allergies, nausea.

Section 5 - Firefighting Measures

Extinguishing Media: CO2, sand, extinguishing powder. Do not use water.
Fire Fighting Procedures: Water with full jet.
Special Protective Equipment for Firefighters: Mouth respiratory protective device.

Section 6 - Accidental Release Measures

Steps to be Taken if Material is Released or Spilled: Dispose contaminated material as waste according to Section 13. Ensure adquate ventilation. Do not fluch with water or aqeous cleansing agents.
Personal Precautions: Wear protective equipment. Keep unprotected persons away.
Environmental Precautions: Do not allow product to reach sewage system or any water course. Inform respective authorities in case of seepage into water course or sewage system. Do not allow to enter sewers/ surface or ground water.

Section 7 - Handling and Storage

General Handling: Ensure good ventilation/exhaustion at the workplace. Open and handle receptacle with care.
Other Precautions: Do not spray on a naked flame or any incandescent material. Keep ignition sources away. Do not smoke. Protect against electrostatic charges. Pressurized container: protect from sunlight and do not expose to temperatures exceeding 50°C, i.e. electric lights. Do not pierce or burn, evan after use.
Storage: Store in a cool location. Observe official regulations on storing packagings with pressurized containers. Keep receptacle tightly sealed. Do not gas-tight seal receptacle. Store in cool, dry conditions in well sealed receptacles. Protect from heat and sunlight.

Section 8 - Precautions to Control Exposure / Personal Protection


Personal Protective Equipment (PPE):

Eye/Face Protection: Tightly sealed goggles.
Skin Protection: Protective gloves are usually adequate when product is used according to instructions. Wear chemical resistant clothing such as gloves, apron, boots or whole bodysuits made from neoprene, as appropriate
Respiratory Protection: In case of brief exposure or low pollution, use respiratory filter device. In case of intensive or longer exposure use, respiratory protective device that is independent of circulating air.
Hygenic Measures: Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Avoid contact with the eyes and skin.
Engineering Controls: Use exhaust ventilation to keep airborne concentration below exposure limits.

Section 9 - Physical and Chemical Properties

Appearance: Aerosol
Color: Clear
Odor: Characteristic
ph: Not determined
Flash Point: -19° C (-2° F)
Upper Flammable Limit: 1.1 Vol%
Lower Flammable Limit: 13.0 Vol%
Autoignition Temperature: 465° C (869° F)
Vapor Pressure: 233.0 hPa (175 mm Hg) at 20° C (68° F)
Boiling Point: 55°C (131° F)
Vapor Density: Not available
Specific Gravity: 0.72 g/cm3
Freezing Point: Not available
Melting Point: Not available
Solubility in Water: notmiscible or difficult to mix
Evaporation Rate: Not available
Partition Coefficient: Not available
Decomposition Temperature: Not available
Percent Volitiles: 97%
Volitile Organic Compounds (VOC): 50.4% 410.4g/l (3.42 lb/gal)
Visosity: Not available

Section 10 - Stability and Reactivity

Stability/Instability: Not available
Conditions To Avoid: No decomposition if used according to specifications.
Incompatible Materials: Not available
Hazardous Decomposition Products: No dangerous decomposition products known

Section 11 - Toxicological Information

Ingestion Toxicity: LD50, Rat 4300 mg/kg (Xylene)
Skin Absorption:LD50, Rabbit 2000mg/kg (Xylene)
No sensitizing effects known.
Eye Irritation
Irritating effect
Skin Irritation
Irritant to skin and mucous membranes.

Section 12 - Ecological Information

Water hazard class 3: extremely hazardous for water. Do not allow product to reach ground water, water course or sewage system, even in small quantities.

Section 13 - Disposal Considerations

Disposal Method:
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
Container Disposal: Disposal must be made according to official regulations.

Section 14 - Transport Information


Proper Shipping Name: Aerosols, flammable
Hazard Class: 2.1
ID Number: UN1950
Packing Group: II

IMDG (Maritime transport)

IMDG Class: 2.1
UN Number: UN1950
Label: 2.1
EMS Number: F-D,S-U
Maritime Marine Pollutant: No
Proper Shipping Name: Aerosols

IATA (Air Transport)

ICAO/IATA Class: 2.1
UN/ID Number: UN1950
Label: 2.1
Proper Shipping Name: Aerosols, flammable

Section 15 - Regulatory Information

Superfund Amendments and Reathorization Act of 1986 (Emergency Planning and Community Right-to-Know Act of 1986) Sections 311 and 312

The following table list hazardous components and the regulatory lists for which they are required to be reported.

Component: Vinyl Acetate Copolymer
CAS Number: 24937-78-8

Component: Acetone
CAS Number: 67-64-1
Amount: 25-50%
Acetone is listed with the Environmental Protection Agency (EPA) as a possible carcinogen.
Acetone is listed with the American Conference on Governmental Industrial Hygenists (ACGIH) as a possible carcinogen.

Component: Heptane
CAS Number: 142-82-5
Amount: 45-50%

Component: 2-Butanone
CAS Number: 78-93-3
Amount: 1-3%

Component: Petroleum gases, liquified, sweetened
CAS Number: 68476-86-8
Amount: 25-50%

Component: Petroleum gases, liquified, sweetened
CAS Number: 68476-86-8
Amount: 25-50%

Component: 2-methoxy-1-methylethyl acetate
CAS Number: 108-65-6
Amount: <2.5%

Component: 2-(propyloxy)ethanol
CAS Number: 2807-30-9
Amount: <2.5%

Component: Chlorinated Polyolefin
CAS Number: N/A

Component: Isobutane/propane aerosol propellant
CAS Number: 68476-86-8
Amount: 4.88%

Component: Xylene
CAS Number: 1330-20-7
Amount: 10-25%
Xylene is listed in SARA 313
Xylene is known to the State of California to cause cancer.
Xylene is listed with the Environmental Protection Agency (EPA) as a possible carcinogen.
Xylene is listed with the Internation Agency for Research on Cancer (IARC) as a possible carcinogen.

HMIS Rating (Scale 0 - 4)

HEALTH  2  Health = 2
FIRE  4  Fire = 4
PHYSICAL  2  Physical = 2
PERSONAL PROTECTION G Personal Protection = G

NFPA Ratings

2 0
Health = 2
Fire = 4
Reactivity =0

Section 16 - Other Information


This Safety Data Sheet (SDS) is prepared in compliance with GHS Hazcom 2012. The information may be based in part on information provided by component suppliers and is believed to be correct as of the date hereof. However, no warranty or merchantability, fitness for any use, or any other warranty is expressed or is to be implied regarding the accuracy of of this data, the results to be obtained from the use of the material, or the hazards connected with such use. Since the information contained herein my be applied under conditions beyond our control and with which we may be unfamiliar, and since data made available subsequent to the date hereof may suggest modification of the information, we assume no responsibility for the result of its use. This information and material is furnished on the condition that the person receiving it shall make his/her own determination as the the suitability of the material for his/her particular purpose and on the condition that he/she assume the risk of his/her use thereof.