Safety Data Sheet

According to GHS (Global Harmonized System) - Hazcom 2012
Date Printed (YYYY-MM-DD): 2018-01-31 

Section 1 - Product and Company Information

Product Name: Filler Prep
Product Part Number(s): 1060FP
Recommended Use: Adhesion promoter that helps filler stick to plastic.
Revision Date (YYYY-MM-DD):

Polyvance24 Hour Emergency ContactChemtrec - 1-800-424-9300 (Outside USA 703-527-3887)
1128 Kirk Rd.Customer Information Number256-638-4103 (7AM - 4PM (CST) M-F)
Rainsville, AL 35986
Information Email:

Section 2 - Hazards Identification

Appearance:Clear liquid
Hazard Statement:
 WARNING! Combustible liquid. May cause an allergic skin reaction. Causes eye irritation.  

Signal Word:  

Signal Word Hazard:   Flammable Liquid
GHS Physical Hazard PictogramsGHS Health Hazard PictogramsGHS Environmental Hazard Pictograms


Not Applicable

GHS Hazards Statement Codes for This Product

Statement Text
Physical H227 Combustible liquid
Health H317 May cause an allergic skin reaction
Health H320 Causes eye irritation
Precautionary Statement:
 Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapours/spray. Do not get in eyes, on skin, or on clothing.  

GHS Precautionary Statement Codes for This Product

Statement Text
General P102 Keep out of reach of children
Prevention P261 Avoid breathing dust/fume/gas/mist/vapours/spray
Prevention P262 Do not get in eyes, on skin, or on clothing

Potential Health Effects

Eye Contact:Nasal and respiratory irritation, dizziness, headache, nausea, possible unconsciousness, and asphyxiation.
Skin Absorption:Moderate irritation, redness, blurred vision.
Inhalation:Dizziness, breathing difficulty, headaches, and loss of coordination.
Ingestion:Gastrointestinal irritation, vomiting, diarrhea.

Section 3 - Composition/Information on Ingredients

Component CAS # ENIECS REACH Reg. No. Amount
2-Butanone 78-93-3 <2%
Chlorinated Polyolefin N/A <3%
Heptane 142-82-5 45-50%
Toluene 108-88-3 45-50%
Vinyl Acetate Copolymer 24937-78-8 <3%

Section 4 - First Aid Measures

Eye Contact: Immediately flush with plenty of water for 15 minutes.
Skin Contact: Flush with plenty of soap and water for 15 minutes.
Inhalation: Remove to fresh air immediately.
Ingestion: If alert, give 2-4 cupfuls of milk/water. Seek medical attention immediately.
Medical Conditions Aggravated by Exposure: Bronchitis, CNS disorders, allergies, nausea.

Section 5 - Firefighting Measures

Extinguishing Media: Foam, CO2, Dry Chemical, Water Fog
Fire Fighting Procedures: Respiratory equipment should be worn to avoid inhalation of concentrated vapors. Water should not be used except as a fog to keep nearby containers cool.
Unusual Fire and Explosion Hazards: Handle as a flammable liquid. Vapors form an explosive mixture in air between the lower and upper explosive limits which can be ignited by many sources such as pilot lights, open flames, electric motors and switches.

Section 6 - Accidental Release Measures

Steps to be Taken if Material is Released or Spilled: Remove all sources of ignition. Allow volatile portion to evaporate completely. Avoid breathing vapors and remove with inert absorbent.
Personal Precautions: Use personal protection recommended in Section 8. Isolate the hazard area and deny entry to unneccesary and unprotected personnel.
Environmental Precautions:

Section 7 - Handling and Storage

General Handling: Reports have associated repeated and prolonged occupational over exposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Avoid spontaneouscombustion of contaminated rags or other ignitable material. Keep out of reach of children.
Other Precautions:
Storage: Do not store near heat, sparks or flame. Store in well ventilated area. Keep closure tight and container upright to prevent leakage. Do not puncture or incinerate. Do not sprat near fire or open flames.

Section 8 - Precautions to Control Exposure / Personal Protection


Personal Protective Equipment (PPE):

Eye/Face Protection: Goggles or side-shielded safety glasses.
Skin Protection: Neoprene or butyl rubber gloves.
Respiratory Protection: Use of a NIOSH approved chemical/mechanical filter, designed to remove a combination of particles and vapors.
Hygenic Measures: Wash hands before eating, smoking or using the washroom.
Other Protection Measures: To prevent repeated or prolonged skin contact, wear impervious clothing and boots. Wash contaminated clothing before reuse.
Engineering Controls: Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLV(s)

Section 9 - Physical and Chemical Properties

Appearance: Clear, petroleum odor
Color: Clear
ph: Not determined
Flash Point: 23F
Upper Flammable Limit: 11.5
Lower Flammable Limit: 1
Autoignition Temperature: Not available
Vapor Pressure: Not available
Boiling Point: 180
Vapor Density: Heavier than air
Specific Gravity: .8
Freezing Point: Not available
Melting Point: Not available
Solubility in Water: Not Soluble
Evaporation Rate: Not available
Partition Coefficient: Not available
Decomposition Temperature: Not available
Visosity: Not available

Section 10 - Stability and Reactivity

Stability/Instability: Stable
Conditions To Avoid: Excessive heat, poor ventilation, open flames, sources of sparks.
Incompatible Materials: Alkaline materials, strong acids, and oxidizing materials.
Hazardous Polymerization: Will Not Occur
Hazardous Decomposition Products: Carbon monoxide, carbon dioxide, various hydrocarbons, oxides of nitrogen, chlorine and possibly acrolein.

Section 11 - Toxicological Information

Mildly toxic by inhalation.

Section 12 - Ecological Information

No Ecological Information available

Section 13 - Disposal Considerations

Disposal Method:
Do not incinerate. Dispose of in accordance with local, state and federal regulations. Do not contaminate lakes, streams or other water supply.
Container Disposal: Disposal must be made according to official regulations.

Section 14 - Transport Information


Proper Shipping Name: Paint related material
Hazard Class: 3
ID Number: UN1263
Packing Group: II

IMDG (Maritime transport)

UN Number: UN1263
Label: Flammable Liquid
Packaging Group: II
EMS Number: F-E, S-E
Maritime Marine Pollutant: No

IATA (Air Transport)

ICAO/IATA Class: 3
UN/ID Number: UN1263
Label: Flammable Liquid
Air Packaging Group: II
Proper Shipping Name: Paint related material

Section 15 - Regulatory Information

Superfund Amendments and Reathorization Act of 1986 (Emergency Planning and Community Right-to-Know Act of 1986) Sections 311 and 312

The following table list hazardous components and the regulatory lists for which they are required to be reported.

Component: Vinyl Acetate Copolymer
CAS Number: 24937-78-8
Amount: <3%

Component: Heptane
CAS Number: 142-82-5
Amount: 45-50%

Component: 2-Butanone
CAS Number: 78-93-3
Amount: <2%

Component: Toluene
CAS Number: 108-88-3
Amount: 45-50%

Component: Chlorinated Polyolefin
CAS Number: N/A
Amount: <3%

HMIS Rating (Scale 0 - 4)

HEALTH  2  Health = 2
FIRE  3  Fire = 3
PHYSICAL  1  Physical = 1
PERSONAL PROTECTION G Personal Protection = G

NFPA Ratings

2 0
Health = 2
Fire = 3
Reactivity =0

Section 16 - Other Information


This Safety Data Sheet (SDS) is prepared in compliance with GHS Hazcom 2012. The information may be based in part on information provided by component suppliers and is believed to be correct as of the date hereof. However, no warranty or merchantability, fitness for any use, or any other warranty is expressed or is to be implied regarding the accuracy of of this data, the results to be obtained from the use of the material, or the hazards connected with such use. Since the information contained herein my be applied under conditions beyond our control and with which we may be unfamiliar, and since data made available subsequent to the date hereof may suggest modification of the information, we assume no responsibility for the result of its use. This information and material is furnished on the condition that the person receiving it shall make his/her own determination as the the suitability of the material for his/her particular purpose and on the condition that he/she assume the risk of his/her use thereof.